Redring WS7 Manuel d'utilisateur télécharger pdf

These instructions should be read in full before commencing the installation.

We recommend that the installation should only be carried out by a suitably qualified person.

The Redring WS7 is an open outlet, thermal storage water heater for use with Redring recommended fittings for one

outlet only. It operates on the displacement principle i.e.; when cold water is admitted into the bottom of the tank, hot

water flows out through the outlet. There are two models: 3kW, which ensures rapid reheating of the water, and a 1kW

unit to suit special electrical requirements.

Fixing

The wall bracket should be securely fixed in

position (see diagram 1). The heater is then hung

on the wall bracket. Further security can be

obtained by marking the position of the extra fixing

holes (see diagram 1) and applying appropriate

wall fixings to these positions.

When the unit is used above the sink with the cold

inlet tap and spout supplied, it is recommended that

these extra fixing positions be used.

The bottom of the heater should be approximately

350mm above the top of the sink.

The outlet should be at least 13mm above the

maximum possible water level for any

appliance that is to be filled from the heater.

Water Connection

(See diagram 4 for suggested installation plan)

Oversink (Diagram 2a)

When using the tap and spout as supplied, the cold

water connection is made directly to the 15mm

compressions fitting

at the rear of the cold inlet tap.

Ensure that the water flow is in line with the flow direction arrow moulded on the cold inlet tap.

Undersink (Diagram 2b)

If the unit is to be mounted below sink level, it should be connected to the special open outlet Monoblock Mixer Tap

recommended by Applied Energy Products Limited (see page 3).

The economic performance of the heater will be enhanced by lagging the hot water pipe from the heater to the outlet.

Oversink and Undersink Installation

Before final assembly of the tap the appropriate restrictor insert must be selected and fitted into the end of the cold inlet

pipe on the heater (see Table A). The correct insert will ensure that the flow rate of water through the heater is at an

optimum to prevent undue mixing of the incoming cold water with the stored hot water, as well as avoiding any

unnecessary pressure within the tank.

Electrical Connection

The installation must be in accordance with the current BS.7671 (IEE Wiring Regulations) and/or local regulations, and

“Part P” of the Building Regulations.

1. The heater is suitable for 240/230V single phase A.C supply.

2. The live (brown) and neutral (blue) wires must be connected to the designated positions in the terminal block and the

earth (green/yellow) to the earth position.

3. WARNING: THIS APPLIANCE MUST BE EARTHED

4. The mains cable should be prepared as shown (see diagram 3)

5. A means for disco

nnection in all poles must be incorporated in the fixed wiring in accordance with the wiring rules.

6. The cable should be heat resisting 3-Core flexible PVC of 0.75mm² for the 1kW model and 1.25mm² minimum for the

3kW model.

7. NOTE – THE APPLIANCE MUST BE FILLED WITH WATER BEFORE POWER IS SWITCHED ON.

Thank you

for choosing a quality

Redring product manufactured in

Peterborough, England

1 2 3 4

(Leaflet No. 578-2018-05A) 4

Résumé du contenu

Page 1

These instructions should be read in full before commencing the installation.

Page 2

2 Usage If the heater is used regularly it is recommended that it is left on at all times. The thick insulation ensures ec

Page 3

3 Suggested Installation Plan Draining the Tank If it is required to drain the tank, this can be effected by undoing the screw in the base plate of

Page 4 - (Leaflet No. 578-2018-05A)

4 Full details of terms and conditions are available on request from: - APPLIED ENERGY PRODUCTS LIMITED, MORLEY WAY, PETERBOROUGH PE2 9JJ TEL +4

Commentaires sur ces manuels

Pas de commentaire

Redring WS7 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Redring WS7. Redring WS7 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Chaudière à eau Redring WS7